SP Particleboard Core Wood Doors

Product Features
And Specifications

Interior Only (1)

For an alternative to our regular particleboard core door, we offer the Marshfield DoorSystems SP Door, using Cold Press Technology with limited options.

Note: These doors are tested for neutral pressure.

Maximum Size

DSP-1: Single: 4/0 x 8/0(11) Pair: 8/0 x 8/0 (11,14)
DSP-20: ITS-WH & UL:
Single: 4/0 x 8/0 (11) Pair: 8/0 x 8/0 (4,11,14)
Double Egress Pair: 8/0 x 8/0 (4,14)1/5-3/4 x 6/0

Minimum Size

1/5-3/4 x 6/0

Face

Wood Veneer door skin, primed hardboard or embossed hardboard.

Stiles

1" two-ply laminated, compatible (9,13),one stile finger jointed.

Top and Bottom Rails

1-1/18", mill option (2,3,9)

Face Assembly Adhesive

Type II (water-resistant)

Core Assembly Adhesive

Type II (water-resistant)

Core (7)

Marshfield DoorSystems particleboard which complies with ANSI A208.1 1-LD-1

Maximum Size of Light Openings (5)

DSP-1: (8)
Total area of openings not to exceed 1296 sq. in of visible glass, or one continuous dimension of 54" in height or one continuous dimension of 38" in width

DSP-20: (6) ITS-WH & UL: Single, Pair & Double Egress Pair:
Total area of openings not to exceed 1296 sq. in. of visible glass or one continuous dimension of 54" in height or one continuous dimension of 30" in width

Factory fitting and machining, factory-standard louvers

Other Detail Work (10)

Factory fitting and machining, factory-standard louvers

Factory Finish

Clear or stain with satin gloss Enviroclad UV^TM finish Prime only Opaque with flat gloss topcoat (12)

Warranty

Limited lifetime; life of original installation (1)

(1) Use of Marshfield DoorSystems doors in exterior applications is not recommended and not warranted.
(2) For doors requiring deep mortise machining on closers, holders, etc., top or bottom rails are a minimum 2-1/2" nominal size.
(3) Wider rails available upon request.
(4) Fire retardant stiles eliminate the need for metal edge and astragal.
(5) Marshfield DoorSystems does not assume responsibility for the choice of glazing materials used. Refer to consumer Product Safety Commission 16 CFR 1201 CAT. 11 (1-1-97 Edition) to determine the need for safety-rated glazing.
(6) Minimum edge margin requirements vary with door types and facings. There must be at least 5-1/2" from light to any edge and adjacent openings, including hardware cutouts on all Marshfield DoorSystems DSP-20-minute fire-rated doors in order to be labeled a fire door.
(7) Surface mounted hardware attached with screws (in I -LD-1 core), requires wide end rails or alternate core construction. Please identify hardware attachment method when specifying/purchasing.
(8) Minimum 5" from light to any edge and adjacent openings, including hardware cutouts.
(9) Laminated Strand Lumber (LSL) or hardwood at mill option for rails and inner ply of stiles.
(10) All Marshfield DoorSystems Fire-Rated doors must be machined by Marshfield DoorSystems or other approved fire door machiners. Factory machining of surface-mounted exit devices with face holes 1" and larger is offered.
(11) Primed hardboard available up to 4/0 x 9/0 singles and 8/0 x 9/0 pairs.
(12) All colors may not be available.
(13) 1-3/8" two-ply laminated compatible stiles available upon request for 1-3/4" thick doors.
(14) Pair doors matched for similar color & grain available upon request.
(15) Positive Pressure doors which meet UBC 7-2-97 requirements are available with ITS-WH labels only.

Note: Marshfield DoorSystems doors are manufactured per the standards listed. Specifications are subject to change without notice.